Online Support
. .
Select Language: English French Spanish

Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player

Effluent Treatment Plant (ETP)


Contributing towards Green Environment

Our ETP plant has been designed to treat the effluent having BOD (Biological Oxygen Demand) above 900 mg/liter which has to reduced to NEQ’S (National Environmental Quality Standards) equal to 80 mg/liter and the COD (Chemical Oxygen Demand) to about 150 mg/liter. The effluent after pH adjustment with Sulphuric acid goes to cooling tower to reduce the temperature from 70 degree.C to 36 to 37 degree.C. then it comes to equalization tank to homogenize the effluent.

Afterwards it goes to Aeration Tank where complete process of aeration is installed and Urea and DAP (Di ammonium phosphate) is being used for the bacterial colony to activate the sludge reducing the BOD and COD, after about 30 hours retention time in aeration tank the over flow goes to clarifier tank where the sludge has been settled into the bottom of clarifier tank. The sludge we used to recycle 50% to back to aeration tank and the remaining 50% goes to filter press to dewatering and to make the cake for proper disposal purposes.

Main Components of our ETP Plant

  • Aeration Tank.
  • Clarifier Tank.
  • Equalization Tank.
  • Sludge Tank.
  • Cooling Tower.
  • Air Blowers.
  • Chemical Dosage Pumps.

Plant Treat Capacity (ETP)

1200 Cubic meter per day. i.e.: 50Cubic meter per hour.

Waste Water Analytical report by SGS 

Dated: 28-Feb-2014

Download Test Report PDF

Waste Water Test Report by SGS

Download Test Report PDF

Chemical Analysis Test Report by GEL PVT. LTD

Download Test Report PDF

ITL Medical And Occupational Health Centre

International Textile has set up state-of-the art medical and healthcare centre for its employees to provide 24/7 healthcare services for medical and first aid cases treatment.

This is located in the center of the unit and enables operating staff to access it with ease, regardless of their plant. In the case of any serious safety incident, it provides a ‘critical holding and stabilization space’ for first-aid administration, until the ambulance gets to the company’s premises. This significantly contributes to the company’s corporate social responsibility (CSR) initiatives.

The centre was inaugurated by Mr. Muhammad Yunus, General Manager Factories and Mr. Akhtar Javed, General Manager Terry Textile Division, on June 29, 2013. The ceremony was attended by our senior and middle management staff and some of our valued business partners i.e. SGS, Aman Foundation and Barlas consultants.

In collaboration with Aman Foundation, the company intends to provide 24/7 tele-consultation services to all of its employees through the healthcentre. Aman foundation will also provide awareness sessions on communicable and noncommunicable diseases which will be helpful in protect health in preventing health and safety hazards at work and also promote healthy life style/ work culture.



This process allows yarn to retain its elastic properties and strength. Our warped yarn, at the end of this process, maintains its stretch thus providing weaving.

Our warping department possesses state-of-the-art Beninger machines, empowering out warping department with the capability of maintaining exact and uniform tension to all wound ends thus allowing warn to retain its elastic properties and strength.

In order to fully ensure absolute uniform density of yarn, the yarn cones used in warping are thoroughly checked which warrant prime quality warping.

International Accreditations

International Accreditations


Worldwide responsible accredited production


International Textile Limited proved its excellence in employee care and social responsibility in the apparel business and earned its certification by meeting global WRAP's (Worldwide responsible accredited production) set of principles, which is regarded as one of the most stringent sets of standards in human rights compliance in apparel manufacturing worldwide.


US Customs-Trade Partnership Against Terrorism (C-TPAT)


As an certified member of the US Customs-Trade Partnership Against Terrorism (C-TPAT) program. Obtaining C-TPAT certification validates that International Textile Limited is recently enrolled top five companies in Pakistan having strong and effective security management system.


Quality Management System


We are well aware that quality management system is vital and we have been trying our best to provide our customers with quality products and service. With ISO certification, customers can be confident and rely on our proven quality management system.

Oeko- Tex

Certification for Fabric & Garments


Your safety and well-being lies at the heart of International Textile. Therefore, ITL strives to ensure that all fabric and accessories which are used in the production are certified to Oeko-Tex Standard 100.

MJS Division


Our Spinning unit is equipped with high-tech machinery and equipment according to the type of processed material and spun yarn. The use of the most advanced machinery enables the adjustment of optimal under pressure for spinning. The quality of spun yarn, the range of processed raw materials, high efficiency of elimination of impurities such as dust and micro-dust place our spinning unit amongst the very best in the region.


Our ISO-9000 and Social Accountability SA-8000 rewards speak volumes about our approach to excellence. Here, we test our yarn so that it is up to the International standards our brands have achieved globally.


We are the pioneers of Murata Jet Spinning in Pakistan and now have the capability to produce yarn counts ranging from 10's to 60's at a speed of 200 to 300 m/min. Not many textile mills in Pakistan follow the MJS technology because it requires high quality workmanship at low-noise level, resulting in better work environment.